LOW POWER SIGNAL
Read more
Optics for sensor profile
Extremely low power consumption
Integrated diagnostic system with visual display
LED indicator for switching status
OSE output signal
IP 67, fully protected electronics
LOW-POWER-SIGNAL automatically selects the output frequency depending on the connected device: safety signals transmitted to a battery-powered radio link will therefore have a lower frequency than if they were sent directly to the control panel via a spiral cable.
This increases battery life and ensures compatibility with most control panels on the market.
Technical specifications
Power supply 3...27 VCC
Maximum door width 1...12 m
Output OSE signal
Warning lights Yellow LED indicator
Connections 3x0,14 mm²
Protection degree IP67, electronics encapsulated in epoxy resin
Data Sheet
SW50
Read more
Pair of built-in photocells
The
SW50 are built-in photocells with a
20 mt range. Due to the recessed shape and size, the SW50 photocell is
interchangeable with the most popular models on the market.
Technical features:.
Power supply: 12/24 VDC/ac
Power consumption: 35 mA
Relay capacity: 1A - 24V
I.R. wavelength: 950 nm
Range: 20 mt
Modulation frequency: 1500 Hz
Synchronized mode: only when supplied with alternating current
Operating temperature: -20°C, +60°C
Datasheet (pdf)
User Manual (pdf)
WS-SIGNAL 15
Read more
Optics for sensor profile
WS-SIGNAL 15 optical profile device is equipped with an integrated diagnostic system that provides an output indicating the quality of the rubber profile. This system is integrated into the transmitter, so no other measuring instruments are required. All visible LED indicators show the switching states.
This enhances operational safety and is also useful for maintenance operations. The precise self-calibration of the sensors ensures consistent switching behavior across all door widths.
Box includes: nr.1 transmitter unit and nr.1 receiver unit
-RJ connector compatible with Hörmann control panels
-Diagnostic system with integrated LEDs
-Switching status indicators
-Insensitive to wind loads and bending
-High immunity to electromagnetic interference (EMC)
-Protection against polarity reversal and short circuits
-Regulated transmitted power
For installation on doors with a modular connector system. WS-SIGNAL optical safety device is an innovative, high-quality product equipped with a modular connector compatible with the Hörmann SKS system.
Diagnostics
After the electronics are powered up, the system evaluates the quality of the rubber profile. The result is displayed as a series of flashes from the LED indicator light, visible on the outside of the profile:
- 01 to 06 flashes: optimal conditions
- 07 to 14 flashes: good conditions
- 15 to 16 flashes: the safety profile is still functional, but operational safety cannot be guaranteed in the long term.
It is recommended to check the rubber profile for possible damage or impurities.
To restart the diagnostics, simply disconnect and then reconnect the power supply.
After the diagnostic indication, the device automatically switches to standard mode, and only the yellow LED lights up when the
light beam is interrupted.
Technical features
Optical range: From 1 to 12 metres, depending on the quality of the rubber profile
Operating voltage: From 10 to 16 VDC, with reverse polarity protection
Electricity consumption: 40 mA (±2 %)
Light type: Pulsed infrared, 880 nm
Diagnostic display: Yellow LED ring for rubber profile diagnostics, flashes from 1 to 16 pulses
Operating display Yellow LED ring lights up when the
safeguard edge is activated
Signal output transistor, max. load 20 mA, protected
against short circuits
Output level: rectangular signal – low: 0 to 1 V / high: 3 to 5 V
Signal frequency: usually 900 Hz
Materials supplied Transmitter: ABS plastic
Receiver: Lexan, IR transparent
Connection cable: PVC, 600 mm with modular connector
Protection degree: IP67 according to EN60529, encapsulated
with 2K epoxy resin
Operating temperature: -25°C,+60°C
Storage temperature: -25°C,+75°C
Weight of receiver: 21gr
Weight of transmitter: 20gr
Data sheet
SPK
Read more
Spiral cable
SPK spiral cables are made from high-quality materials, making them suitable for the most intensive installations. The extension factor is four times the block length (BL).
Spiral cables are resistant to microbes, hydrolysis and almost all mineral oils, thanks to a special sheath compound.
In addition, spiral cables are UV-stable and halogen-free.
The material is black PUR/PUR, the colour of the wires complies with DIN 47100:
3 wires = brown, white, green
4 wires = brown, white, green, yellow
5 wires = brown, white, green, yellow, grey
6 wires = brown, white, green, yellow, grey, pink
Variable cable ends (see table), including 40, 50, 60, 80, 100 or 200 mm without sheath and equipped with cable lugs (AEH).
Data sheet
