AP2
Read more
Control unit for 230V sliding gates
Equivalent replacement for discontinued T2E control units.
This electronic control unit is an equivalent replacement for the T2E, perfectly pin-to-pin compatible and suitable for installation on sliding gates with 230V motors.
Designed to ensure maximum operational continuity even on systems no longer supported by the original manufacturer, it allows for rapid and reliable updating of existing automation without system modifications.
Supplied without a container, it is perfect for maintenance and restoration operations on older systems, maintaining performance levels unchanged.
Combined with the UN-SE 433.92 MHz receiver unit (APE-117/0433), the control panel's compatibility is also extended to the T22 model.
Technical specifications:
- Supply voltage: 230 Vac (+6% / -10%) – 50Hz
- Stand-by power consumption: 15 W
- Operating power consumption: 680 W (with motors and accessories connected and ready to use)
- Operating temperature: -20°C, +70°C
- Storage temperature: -40°C, +85°C
- Relative humidity: max 90% (non-condensing)
- Supplied without PVC container
ALCR-36N
Read more
Compatible control unit for swing gates, 230V
Equivalent replacement for Alcor discontinued control units.
La centrale The ALCR-36N control unit is designed to control one or two 230V hydraulic or electromechanical operators and has been developed to directly replace discontinued control units.
Full electrical and functional compatibility makes it an ideal solution for restoring existing systems, allowing for rapid upgrades without any wiring modifications.
The control unit includes a 433 MHz radio receiver (rolling code and fixed code), supports the storage of up to 200 transmitters, and allows flexible management of operating logic: step-by-step, condominium, 4 steps and 4 steps plus. It also features specific configurations for hydraulic motors, photocell management, 12/24V or 230V electric locks, and electronic force adjustment.
Features and functionality:
Power supply: 230 Vac
No. of motors: 1 or 2 hydraulic or electromechanical motors
Maximum motor power: 0.5 Hp max
Accessory voltage: 24 Vac – max 8 W
Flexible automatic closing time: up to 240 seconds
Flashing output voltage and courtesy light: 230 Vac – max 40 W
Electrical lock output voltage: 12/24 V or 230 Vac
On-board receiver: 433 MHz, rolling code or fixed code
Storable transmitters: up to 200
Operating temperature: -20°C / +55°C
Selectable logic: step-by-step, condominium, 4 steps, 4 steps plus
Advanced functions: slowdown, water hammer, pedestrian opening, rapid closing
Photocell control (FAP and FCH) with DIP switch exclusion
Instruction Manual
STICK RG
Read more
Plug-in receiver compatible with fixed code, rolling code and HCS remote controls – 433.92÷868 MHz
This multi-frequency plug-in receiver is designed for direct integration into control units, equipped with a specific connector, offering maximum flexibility in radio command management.
It is compatible with most fixed code, rolling code and HCS radio controls operating in the 433.92 MHz and 868 MHz bands.
Equipped with two independent channels, configurable in pulse, bistable or timer mode (in seconds or minutes), it allows the control of multiple devices or functions from a single unit.
The on-board memory can store up to 250 remote controls, with a quick and easy storage procedure by self-learning.
Multi-frequency compatibility and configuration versatility make it the ideal solution for replacing universal plug-in receivers used in automation systems.
Technical features:
- Operating frequency: 433.92 ÷ 868 MHz
- Compatible with fixed codes, rolling codes and HCS
- Power supply: +5 Vdc
- Power consumption: 25 mA typical / 50 mA max
- 2 independent channels (Ch1 and Ch2)
- Output modes: impulsive, bistable, timer in seconds or minutes
- Channel output: +3 Vdc
- Memory capacity: up to 250 remote controls
- Quick programming with self-learning
- Single or total deletion of stored codes
- Status LED and code/error indication
- Compact dimensions: 49×31×11 mm
- Operating temperature: -10°C to +50°C
AZ33
Read more
Compatible control unit for 230V swing gates
Equivalent replacement for ZA3 discontinued control units.
The AZ33 control unit is designed to control one or two 230V electromechanical motors for swing gates and is fully compatible with the ZA3 discontinued versions.
Full functional compatibility and removable terminals provide an immediate and safe replacement solution for restoring existing systems without modifying the original wiring.
The board includes several advanced features: electronic motor force adjustment, photocell management, step-by-step control and partial opening, courtesy light and flashing light output, water hammer function, dead man's switch mode and logic suitable for condominium contexts.
The on-board connector allows the use of the main radio modules at 433.92 MHz or 30.900 MHz.
Features and functionality:
Power supply: 230 Vac
No. of motors: 1 or 2 motors
Motor power supply: 230Vac (600 W max per motor)
Maximum motor power: 0.5 Hp max
Motor power adjustment: 50–100%
Flexible operating time: up to 80 seconds
Output voltage services: 24 Vac – max 20 W
Flexible automatic closing time: up to 120 seconds
Flashing output voltage and courtesy light: 230 Vac – max 200 W
Electrical lock output voltage: 12 Vac – max 15 W
Gate open indicator output voltage: 24 Vac – 3 W
Radio modules: grafting 433.92 MHz or 30.900 MHz (not included)
Auxiliary relay output: 230 Vac – max 15 A
Circuit breaker: 5 A
Fuse 12-24: 3.15 A
Operating temperature: -10°C / +50°C
Humidity: <95% (non-condensing)
Selectable logic: step-by-step, condominium, dead man's switch
Advanced functions: slowdown, water hammer, partial opening
Photocell control (FAP and FCH) with DIP switch exclusion
