LOW POWER SIGNAL
LOW POWER SIGNAL - Image 2
LOW POWER SIGNAL - Image 3
LOW POWER SIGNAL - Image 4

LOW POWER SIGNAL

Category:

Optics for sensor profile

Extremely low power consumption
Integrated diagnostic system with visual display
LED indicator for switching status
OSE output signal
IP 67, fully protected electronics

LOW-POWER-SIGNAL automatically selects the output frequency depending on the connected device: safety signals transmitted to a battery-powered radio link will therefore have a lower frequency than if they were sent directly to the control panel via a spiral cable.
This increases battery life and ensures compatibility with most control panels on the market.

Technical specifications
Power supply 3…27 VCC
Maximum door width 1…12 m
Output OSE signal
Warning lights Yellow LED indicator
Connections 3×0,14 mm²
Protection degree IP67, electronics encapsulated in epoxy resin

Data Sheet

REQUEST INFORMATION

Related products

  • WS-SIGNAL 15

    WS-SIGNAL 15

    Read more

    Optics for sensor profile

    WS-SIGNAL 15 optical  profile device is equipped with an integrated diagnostic system that provides an output indicating the quality of the rubber profile. This system is integrated into the transmitter, so no other measuring instruments are required. All visible LED indicators show the switching states. This enhances operational safety and is also useful for maintenance operations. The precise self-calibration of the sensors ensures consistent switching behavior across all door widths. Box includes: nr.1 transmitter unit and nr.1 receiver unit -RJ connector compatible with Hörmann control panels -Diagnostic system with integrated LEDs -Switching status indicators -Insensitive to wind loads and bending -High immunity to electromagnetic interference (EMC) -Protection against polarity reversal and short circuits -Regulated transmitted power   For installation on doors with a modular connector system. WS-SIGNAL optical safety device is an innovative, high-quality product equipped with a modular connector compatible with the Hörmann SKS system. Diagnostics After the electronics are powered up, the system evaluates the quality of the rubber profile. The result is displayed as a series of flashes from the LED indicator light, visible on the outside of the profile: - 01 to 06 flashes: optimal conditions - 07 to 14 flashes: good conditions - 15 to 16 flashes: the safety profile is still functional, but operational safety cannot be guaranteed in the long term. It is recommended to check the rubber profile for possible damage or impurities. To restart the diagnostics, simply disconnect and then reconnect the power supply. After the diagnostic indication, the device automatically switches to standard mode, and only the yellow LED lights up when the light beam is interrupted. Technical features Optical range: From 1 to 12 metres, depending on the quality of the rubber profile Operating voltage: From 10 to 16 VDC, with reverse polarity protection Electricity consumption: 40 mA (±2 %) Light type: Pulsed infrared, 880 nm Diagnostic display: Yellow LED ring for rubber profile diagnostics, flashes from 1 to 16 pulses Operating display Yellow LED ring lights up when the safeguard edge is activated Signal output transistor, max. load 20 mA, protected against short circuits Output level: rectangular signal – low: 0 to 1 V / high: 3 to 5 V Signal frequency: usually 900 Hz Materials supplied Transmitter: ABS plastic Receiver: Lexan, IR transparent Connection cable: PVC, 600 mm with modular connector Protection degree: IP67 according to EN60529, encapsulated with 2K epoxy resin Operating temperature: -25°C,+60°C Storage temperature: -25°C,+75°C Weight of receiver: 21gr Weight of transmitter: 20gr Data sheet
  • ACTIVE R3, bordo sensibile radio

    ACTIVE-R3

    Read more
    Radio Safety Edge
    The ACTIVE-R3 safety edge is a small and discreet safety edge with conductive technology that ensures rapid response to impacts, over the entire length of the structure. The ACTIVE-R safety edge transmits the signal through the built-in two-way radio transmitter (868 MHz) powered by two 3.6V lithium batteries. This edge is certified as a safety device cat.2, EN 12978.. The ACTIVE-R is easy to install and can be shortened to make it perfectly fit your needs. Available in sizes 1.20 - 1.60 - 2.00 - 2.50 mt. TECHNICAL DATA: - Operating temperature: -20°C, 55°C; - Frequency: 868 Mhz - Degree of protection: IP65; Find out other safety edges: ACTIVE, wired safety edge; CAPTIVE, Crashless (crash avoidance) safety edge.  
  • SW50 fotocellule da incasso intercambiabili con le più diffuse marche sul mercato

    SW50

    Read more
    Pair of built-in photocells The SW50 are built-in photocells with a 20 mt range. Due to the recessed shape and size, the SW50 photocell is interchangeable with the most popular models on the market. Technical features:. Power supply: 12/24 VDC/ac Power consumption: 35 mA Relay capacity: 1A - 24V I.R. wavelength: 950 nm Range: 20 mt Modulation frequency: 1500 Hz Synchronized mode: only when supplied with alternating current Operating temperature: -20°C, +60°C   Datasheet (pdf)   User Manual (pdf)
  • P41 coppia di fotocellule a infarossi orientabili, portata 15 mt

    P41

    Read more
    Pair of adjustable infrared photocells The P41 photocells are adjustable and with a range of up to 15 meters. Technical features: Power supply: 12/24 Vdc/ac Absorption: 60 mA Relay capacity: 1A – 24V I.R. wavelength: 880 nm Range: 15 mt Modulation frequency: 1500 Hz Synchronized mode: only when supplied with alternating current Operating temperature: -20°C, +60°C   Datasheet (pdf)   User Manual (pdf)
Top