L36
Read more
Laser technology sensor for industrial gates and doors
L36 is an innovative photocell based on time-of-flight (ToF)
laser technology, designed for use on gates as a security device.
Compared to traditional photocells,
it does not require two devices or reflectors. L36 uses a laser rangefinder to measure the distance to an obstacle.
The photocell can be used in 3 diff erent modes:
Mode A
OPERATION AS A PHOTOCELL
This mode requires a fixed physical reference point opposite the laser rangefinder. Maximum detection distance: 9 m.
The photocell analyses two events. Obstacle detection at shorter distance than the stored distance, during the learning phase.
Mode B
OPERATION AS A PROXIMITY SENSOR (APPROACH PERPENDICULAR TO THE LASER BEAM)
Maximum reading distance 6 m, optimised for detecting movements perpendicular to the beam.
The reading distance is programmable and can be adjusted in increments of 0.5 m during programming.
Mode C
OPERATION AS A SENSOR APPROACHING THE PHOTOCELL FROM ANY DIRECTION
Maximum reading distance 6 m, optimised for detecting movements approaching the photocell from any direction.
The reading distance is programmable and can be adjusted in increments of 0.5 m during programming.
Technical characteristics:
Power supply: 12-24V AC/DC
Transmission/reception angle: +/- 25°
Head rotation angle: 180°
Maximum range
Mode A: 9 m
Modes B and C: 6 m
Maximum output load: 30Vdc, 0.5A
Operating temperature: -10°C to +60°C
Protection class: IP54
Dimensions: 36x123x33 mm
Weight: 69 g
Data Sheet
Instruction Manual
LZR-I100/LZR-I110
Read more
Security sensor for swing and sliding gates and industrial doors
LZR-i100 and LZR-i110 detectors are based on highly accurate time-of-flight technology, ensuring optimal safety at the threshold and in the proximity of the door, with four laser curtains that define corresponding detection areas.
PERFORMANCE
- Adjustable detection area depth (up to 1 m) depending on installation height
- Certified safety solution for industrial doors: PL “d” / CAT 2 according to EN ISO 13849-1 and type E according to EN 12453
- High level of safety with complete three-dimensional detection in front of the door
- Small object detection
APPLICATIONS
- Safety during door opening and closing with 2 separate detection zones
- Possibility to create 2 virtual buttons for door opening
DESIGNED FOR INDUSTRIAL CONTEXTS
- Filters door vibrations and environmental interference
- Filters door frame deformations caused by wind
- Protection rating IP65
Technical features
LZR-i110 - Maximum detection distance: 5 m × 5 m
LZR-i100 - Maximum detection distance: 9.9 m × 9.9 m
Power supply: 10-35V DC on connector
Output: 2 electronic relays (galvanic isolation –
polarity-free)
Maximum switching voltage: 35 VDC / 24 VAC
Maximum switchable current: 80 mA (resistive)
Dimensions: 125 mm (W) × 93 mm (D) × 70 mm (H)
(mounting bracket +14 mm)
Protection rating: IP65
Operating temperature: -30°C to +60°C under power
Compliance: EMC 2014/30/EU; LVD 2014/35/EU; MD
2006/42/EC; ROHS 2 2011/65/EU; EN 12453 chapter
5.1.1.6, chapter 5.5.1 Safety device E; EN 12978; EN ISO
13849-1 Pl ‘d’/ CAT2; EN 60529; IEC 60825-1; EN
60950-1; EN 61000-6-2; EN 61000-6-3; IEC 61496-1; EN
61496-3 ESPE Type2; EN 62061: 2005 SIL 2; DIN 18650-1
Chapter 5.7.4
Data sheet
Instructions Manual
LZR-S600
Read more
Laser detector for building security
LZR-S600 is a LASER security detector designed to protect property and buildings from theft, intrusion and vandalism. It is a compact, easy-to-install, plug & play solution with a self learning function.
- Ability to detect small objects with a reflectivity factor of 2%
- Does not require illumination of the object to be protected (unlike standard camera systems)
- Effective protection against environmental disturbances (flight time and special software)
Technical features
Maximum detection distance: from 10×10 to 25×25 (4 planes in height, width, and depth)
Detection mode: motion and presence
Power supply: 10–35 V DC via connector
Output: 2 independent relays con gurable as
pre-alarm/alarm, day/night, anti-vandalism
Protection rating: IP65
Operating temperature: -30°C to +60°C under power
Compliance: 2006/95/EC: LVD; 2002/95/EC: RoHS;
2004/108/EC: EMC ; EN 60529:2001; IEC 60825 - 1: 2007
Laser Class 1 & 3R ; EN 61000-6-2: 2005 EMC - Industrial
level ; EN 61000-6-3: 2006 EMC - Commercial level
Data Sheet
Instructions Manual
WS-SIGNAL 15
Read more
Optics for sensor profile
WS-SIGNAL 15 optical profile device is equipped with an integrated diagnostic system that provides an output indicating the quality of the rubber profile. This system is integrated into the transmitter, so no other measuring instruments are required. All visible LED indicators show the switching states.
This enhances operational safety and is also useful for maintenance operations. The precise self-calibration of the sensors ensures consistent switching behavior across all door widths.
Box includes: nr.1 transmitter unit and nr.1 receiver unit
-RJ connector compatible with Hörmann control panels
-Diagnostic system with integrated LEDs
-Switching status indicators
-Insensitive to wind loads and bending
-High immunity to electromagnetic interference (EMC)
-Protection against polarity reversal and short circuits
-Regulated transmitted power
For installation on doors with a modular connector system. WS-SIGNAL optical safety device is an innovative, high-quality product equipped with a modular connector compatible with the Hörmann SKS system.
Diagnostics
After the electronics are powered up, the system evaluates the quality of the rubber profile. The result is displayed as a series of flashes from the LED indicator light, visible on the outside of the profile:
- 01 to 06 flashes: optimal conditions
- 07 to 14 flashes: good conditions
- 15 to 16 flashes: the safety profile is still functional, but operational safety cannot be guaranteed in the long term.
It is recommended to check the rubber profile for possible damage or impurities.
To restart the diagnostics, simply disconnect and then reconnect the power supply.
After the diagnostic indication, the device automatically switches to standard mode, and only the yellow LED lights up when the
light beam is interrupted.
Technical features
Optical range: From 1 to 12 metres, depending on the quality of the rubber profile
Operating voltage: From 10 to 16 VDC, with reverse polarity protection
Electricity consumption: 40 mA (±2 %)
Light type: Pulsed infrared, 880 nm
Diagnostic display: Yellow LED ring for rubber profile diagnostics, flashes from 1 to 16 pulses
Operating display Yellow LED ring lights up when the
safeguard edge is activated
Signal output transistor, max. load 20 mA, protected
against short circuits
Output level: rectangular signal – low: 0 to 1 V / high: 3 to 5 V
Signal frequency: usually 900 Hz
Materials supplied Transmitter: ABS plastic
Receiver: Lexan, IR transparent
Connection cable: PVC, 600 mm with modular connector
Protection degree: IP67 according to EN60529, encapsulated
with 2K epoxy resin
Operating temperature: -25°C,+60°C
Storage temperature: -25°C,+75°C
Weight of receiver: 21gr
Weight of transmitter: 20gr
Data sheet
